Using a conduit bender

Mark the beginning and end of the desired bend along with a longitudinal line on the side of the pipe opposite to the. The two sides of the bend should align with the two legs of the square indicating that the bend is at exactly 90 degrees.

Mark the conduit 8 from the end.

Using a conduit bender. Bending conduit can be frustrating without the proper materials. But by using a pipe and. A proper bend is made by rolling the conduit about the bender in the conduits cradle using all foot pressure.

Use the correct size bender for the conduit size being bent. Some over bending may be required to allow for spring back of the conduit. The resting condition of the conduit is to be at the final angle desired.

Put the hilt of the bender on the ground. Secure it in place with both feet or another reliable anchor. Keep the bender straight and let your body apply the pressure to the conduit.

Dont try to use the bender to airbend. Make sure the head of the bender stays rigid as the conduit bends into the. I demonstrate some basics about bending cheap electrical conduit and make a stand for my homemade bbg smokerElectrical conduit can have many uses other than.

Intro to the conduit bender and indicators you can find on them. Begin by estimating the needed length of tube or pipe. Mark the beginning and end of the desired bend along with a longitudinal line on the side of the pipe opposite to the.

Bend a test pipe 90 degrees to use as a reference. Check the angle of the pipe by laying it against a carpenters square. Remove the conduit from the bender and check your work with a framing square.

The two sides of the bend should align with the two legs of the square indicating that the bend is at exactly 90 degrees. Next check the length of the bend. Position the conduit with the long end on the floor and the short end pointing upward.

Line up arrow on either side of hook with guideline and make 45 bend in tube. Reverse tube in bender and adjust so that X is lined up with inch-mark on bender corresponding to depth of offset desired. Line up guide-line with opposite arrow and make second 45 bend.

The follower block is kept loose so as to adjust the height when inserting the tube. Hold the pipe in between the follower block and the die. Vertically align the block to the pipe and then insert the pipe into the machine.

The die will rotate outwards as you insert the pipe. Consider making a 14 stub using a 34EMT conduit. The IDEAL bender indicates stubs 6 to.

Simply subtract the take-up or 6 from the finished stub height. In this case 14 minus 6 8. Mark the conduit 8 from the end.

Line up the Arrow on the bender with the mark on the conduit and bend to 90. Use an EMT bender to bend 30 kick in the PVC conduit by bending it to 60 and then the conduit will spring back to 30. This will only work on ½ or ¾ PVC and only for small bends but it is fast and pretty acc urate.

This document will walk a beginning electrician through the steps to bend EMT tubing with a hand EMT tubing bender. Measure the length of conduit where you need the 90 to be and mark. Place the bender on the conduit with the hook pointing towards to short end and align the mark with the tip of the star.

Place one foot on the conduit and the other foot onto the bender foot. Grab the handle and using foot pressure on the bender foot and bend the conduit. If your conduit bend isnt quite right an easy way to adjust it is to slide the handle of the bender over the conduit and bend it a little one way or the other.

And heres how to know if your 90-degree bend is really 90 degrees. After bending the conduit place one leg of the bend vertically against the wall and the other leg on the floor. Before you begin your bend use a conduit reamer to remove any cutting burrs left after youve made your cut.

Some electricians use a knife to swipe the edge of the cut. Dont use a screwdriver. Its not meant for this task and really doesnt work as well.

Mark the distance at which the conduit must change direction. Conduit Bender and Handle This conduit bender accurately and consistently This conduit bender accurately and consistently performs common bends such as stub-ups offsets back-to-back and saddle bends. Create bends in lengths of conduit by using the 1 in.

Also bends 1 in. Thin wallEMT or 34 in. BendWorks Software ensures that all conduit runs are error-free and export-ready for prefabrication or on-site bending with most Greenlee benders saving time and reducing cost for the electrical contractor.

BendWorks is covered by one or more of the following US. 8886348 9298180 and 9886024. Klein Tools 51612 Conduit Bender 34-Inch Angle Setter for use with Klein Tools Conduit Benders Cat No.

51607 997 9. 97 1296 1296 FREE Shipping on orders over 25 shipped by Amazon. Only a few numbers and math operations need to be memorized to make offsets saddles and 90 degree bends.

Even the multiplier and deduct figures are usually stamped onto the bender device. For more information on using a hand bender see my comprehensive guide to bending conduit.