08
Mar
There is a section of the tie rod on the inside of the ball joint that has flat spots to get a open end wrench onto. 25-102 part plus 60-150 labor.
You must remove or slide the inner tie rod boot outward on the rod and then thread the tie rod out of the steering rack.
Tools needed to change tie rods. This inner tie rod removal tool set makes it easy to replace inner tie rods without removing the rack and pinion. The inner tie rod removal set includes seven SAE and metric adapters to handle a variety of make and model vehicles. The set is constructed of forged steel and comes organized in a custom case for easy storage and transport.
Things Youll Need Accessing the Tie Rod EndTire Iron or Impact WrenchFloor JackJack Stands Tire Iron or Impact Wrench Floor Jack Jack Stands Removing the Tie Rod EndsNeedle Nose PliersOpen End WrenchRatchet or ImpactTie Rod PullerHammer or Mallet Needle Nose Pliers Open End Wrench Ratchet. Tie rods ball joints and other suspension components require specific tools to properly service and replace them. These could include separators crowfoot tools pullers presses and a number of other specialty tools made to get the job done right.
The tools you need to service your tie rods and other suspension parts can be found at OReilly Auto Parts. There are a few tools you will need to replace your tie rod ends. These include a torque wrench a ratchet 22 and 24 sockets pliers a flat-head screwdriver wire cutters 27 and 32 open-ended wrenches a crescent wrench Loctite for threads a hammer and chisel or punch.
Removing outer tie rod end. Part 1 of 1. Replacing your tie rod ends ½ inch breaker bar ½ inch socket 19mm and 21mm ⅜ inch ratchet ⅜ socket set 10mm-19mm Combination wrenches 13mm-24mm Cotter pins 2 Floor Jack Gloves Liquid marking pen Safety jack stands 2 Safety glasses Tie rod s Tie rod puller tool.
How to replace inner and outer tie rods. This video will show you in depth how to change the inner and outer tie rods of your car or truck. You need a specia.
You will need a 18 mm wrench or socket 78 wrench a tie rod end separator and a inner tie rod tool to get the inner tie rod off you will also need a pair of pliers to get the clamps off or the inner boot. Use a two-jaw or tie rod end puller to remove the tie rod end from the steering knuckle. Start slowly in order to seat the tool properly for good leverage.
Mark the position of the tie rod end on steering assembly with chalk or electrical tape then remove by unscrewing. Use a breaker bar with a 22mm socket to remove the bolt on the upper tie rod. Place a tie rod removal tool in between the tie rod and ball joint ends.
Use a hammer to drive the tool in further and separate the outer end of the tie rod. Use a Crescent wrench to loosen the lock nut on the inner end of the tie rod. Remove the tie rod and set it aside.
Correct way is to remove the outer tie rod end and use correct long socket for the inner tie rod after removing boot but alot of shops will just crank far left and right to expose the inner tie rod socket area where it attaches at the rack and pinion and use large wrench to break loose and then unthread. You must remove or slide the inner tie rod boot outward on the rod and then thread the tie rod out of the steering rack. There is a section of the tie rod on the inside of the ball joint that has flat spots to get a open end wrench onto.
To check your tie rods simply jack the wheel off of the ground grab the either side of the tire and wiggle it towards and away from you. If you feel any play at all the tie rods must be replaced. Also a god indication is when the front tires start to wear.
Tie rods are not very expensive to replace. The outer tie rod replacement costs 20-95 part plus 50-110 labor. Replacing the inner tie rod end costs a little more.
25-102 part plus 60-150 labor. In many cars a special tool is required to replace inner tie rod ends. Does the vehicle need the wheel alignment after replacing a tie rod end.
This is the most severe sign. A broken tie rod causes steering loss which could lead to an accident. This is why manufacturers take these components seriously and recall a vehicle if theres a chance they were misassembled at the factory.
How to tell if tie rods are bad. Fortunately its simple to check if the tie rods are bad. Inner tie rods are a little harder to replace than outer tie rod ends.
They usually require an inner tie rod removal tool to disconnect them from the rack. Grease the zerk fittings on outer tie rod ends during every lube oil and filter service. Picked Fork Kit on Amazon - httpamznto2Hr3Blazer Jimmy S10 Replacement Tie Rod Ends on Amazon - httpamznto2CeBhyVGrease Gun on Amazon - https.
Need a thin open end wrench. Start with a high quality standard one and grind it down in thickness. Keep dipping it in water as you grind so as to not affect the heat treating the wrench would have.