Removing dents from plastic bumpers

The kit includes two sizes of each tool according to a press release and completes Polyvances other dent removal tool options. Heat the area of the dent from underneath the bumper cover.

Firstly apply a bit of water on both the plunger and the dent.

Removing dents from plastic bumpers. As the plastic heats up Scott uses a glove to push up from behind the dent with his hand to test how pliable the plastic is becoming with the heat. Once the plastic begins to get warm to hot he begins to push up from the inside as he focuses his heat around the perimeter of the dent. As the dent begins to shrink he brings his rotations with the heat gun inwards to match.

Once the dent starts to release it will quickly begin to shrink. Carefully take the dry ice in one hand and rub it gently against the dent for a few minutes. The dent should pop out as the plastic contracts in response to the cold.

If that does not happen proceed to Step 2. Wait an hour or so before attempting this step to allow the plastic to heat back to a normal temperature. From there take a hair dryer and apply heat directly to the area.

Step 1 Determine if you can use this method. This will only work if your car allows you to get underneath it and access the dented area of the cover from the underside. If not use the other methodStep 2 Turn on your heater blower.

Start to heat around the area of dent in circular motionStep 3 Lay on the ground under the area where the dent is and have the heater blower ready to use. Heat the area of the dent from underneath the bumper cover. Heat around the dent in circular motion.

The illustration shows the approximate size and location of the dent. Caveats-some people say you can use suction cups or a plunger to pull the dent. I couldnt make it work in this case but its easy and worth a try.

-if you can get behind the dent you may be able to push it out -You should try to pull the dent as soon as possible. Performing the PDR Bumper Repair Access the dent. Since you cannot glue pull plastic dents you will need to gain access behind every bumper repair.

This does not mean you have to take it off though. Depending on where the dent is located you may only need to take off one side so that it is hanging enough for you to get in behind. When you have access to the area behind the bumper and the dent is a minor one you will find it can be fixed with the use of a heat gun or hair dryer.

Heat guns can reach very high temperatures so be sure you are wearing heat-resistant gloves clothes and eyewear when performing this repair. This method works for dents on plastic bumpers as well as on parts of your car made of plastic. Boil a pot of water and pour it over the dented area on your bumper.

Reach behind the bumper and pop the dent outYou might also need to take the bumper off if the dent cant be reached. How to fix bumper dents on your car using hot water and a hammer. Since plastic is flexible when its hot this is something you can easily do at home with simple hand tools.

How to fix car dents. You can remove most small dents from your vehicle with a hair dryer and compressed air dry ice or even hot glue and corks but if it happens to be isolated on your bumper all you need is some boiling water. 8 Easy Ways to Remove Dents Without Ruining the Paint Yes Some Really Hot Water Could Be All You Need.

If the first step does not work try to heat the plastic bumper with a hairdryer. Turn the dryer to the high hot setting and make sure you blow-dry the dented area in a continual sweeping motion for about three minutes. Then try to push the dent out manually once again this time using heat-resistant gloves to protect your hands from the warmth.

Removing dents from plastic bumpers When a plastic bumper is dented the plastic becomes very stressed. All of the stresses need to be released in order to remove the dent correctly. The only way to do this is with the correct amount of heat and pressure in the right areas.

5 2021Polyvance has released a new tool the 6119 Dent Driver kit designed to help technicians remove dents from vehicles with plastic bumpers. The kit includes two sizes of each tool according to a press release and completes Polyvances other dent removal tool options. Firstly apply a bit of water on both the plunger and the dent.

Then press the plunger on to the dent and pull with all the strength you can muster. Dont just pull from the one angle. Make sure that you apply the plunger all around the dent especially if its been a sizable knock.

Apply a Hairdryer to the Dent. Rainsville Ala Polyvances new 6119 Dent Drivers tool kit will help shops remove dents from plastic bumpers keeping labor hours in the shop and damaged plastic out of the landfill. The 6119 Dent Driver kit includes two each of two different-sized tools for a total of four tools.

Polyvance s new 6119 Dent Driver kit is a specialized tool set to help the auto body technician remove dents from plastic bumpers. The kit includes two each of two different-sized tools for a total of four tools. Push the dented area back to its original position - Once you have heated the plastic bumper cover to the appropriate temperature place your custom-made dent removal tool behind the bumper cover and gently push it into the softened plastic.