Radiator drain and fill

Drain coolant at crankcase. Drain Point - Locate the drain point on the radiator.

5 Plastic bottle cut and used as a funnel.

Radiator drain and fill. To drain your old antifreeze start by removing your fill cap. The fill cap can be on the radiator the engine the pressure tank or one of your hoses. Locate the petcock Locate the petcock a small shut-off valve which will be located on the bottom of one of the radiator tanks.

The traditional coolant draining process is also known as drain and fill This involves simply draining the coolant at the bottom of the radiator then topping up the radiator with fresh fluid until it its full. To flush the cooling system refill the radiator with plain water. Then start the engine and allow it to run until it is at operating temperature while keeping the radiator or reservoir full.

Once the engine is warm and the thermostat has opened shut the engine off and repeat the draining process motioned earlier in this guide. Open the radiator fill cap usually on top of the radiator. If your vehicle has a plastic tank or reservoir for coolant open that cap too.

Consult the vehicle owners manual for the location of the radiator petcock or drain and position the container on the ground under that drain so its ready to capture the escaping antifreeze. Drain coolant from radiator 5 Slide collector siphon hose onto fitting at radiator 3. 6 Open the radiator drain plug 4 and drain the Catch coolant with suitable vessel.

Coolant 7 Tighten radiator drain plug 4 and detach collector siphon hose from fitting at radiator 3. Drain coolant at crankcase. At Firestone Complete Auto Care we offer more than just a drain-and-fill Our expert technicians will assess the state of your radiator and service your cooling system fully.

Firestone radiator fluid exchange service includes. Addition of flush chemicals sealant and lubricant. How much does Radiator Flush cost in Union City NJ.

Get an estimate instantly. Service parts cost recommendations from YourMechanic. Your definitive guide to Radiator Flush in Union City NJ.

Radiator Coolant Fluid Exchange. Help keep your engine cool in the summer and warm in the winter. Based on your manufacturers recommendation andor test results Jiffy Lube removes used engine coolant also called antifreeze replaces it with coolant that meets or exceeds your manufacturer specifications and properly disposes of the used fluid.

Used to drain the Radiator and Low Temperature Radiator LTR. 3688493C2 is needed to use this tool. For LT RH and HX Series Trucks use Coupling pn.

BRITPART BRASS PLUG DRAIN AND O RING KIT FOR RADIATOR FILLER COMPATIBLE WITH LAND ROVER DISCOVERY 1 1994-1999 V8 MODEL PART ERR4686B ERR4686 ERR4685. 44 out of 5 stars 6. Only 11 left in stock - order soon.

URO Parts 17111437361 Radiator Drain Plug with O-ring. Drain Point - Locate the drain point on the radiator. Drain Coolant - Drain the coolant from the system.

Circulate Water - Run engine with distilled water and flush. Fill Coolant - Dilute coolant with distilled water and fill. Locate Hoses - Locate the coolant hoses and connection points.

Flush the radiator with tap water until the drainage runs clear. Repeat filling the radiator with 1 gallon 38 L of tap water running the car with the heat on and draining it once its cooled. Once the water runs clear flush the system one last time with distilled water.

Place a drain pan under the radiator drain cock in order to collect all the used coolant. Open the radiator drain cock. Remove the right side engine block drain hole plug.

Engine Drain Right Side. Remove the left side engine block drain hole plug. Engine Drain Left Side.

Allow the cooling system to drain completely. There are two ways to fill the radiator. The first procedure is to take the upper radiator hose off and pour the radiator coolant in until the radiator is full.

Then you replace the radiator hose and fill the coolant surge tank bottle to the correct level cold fill line. Drain the old mixture into a container. Replace the radiator drain plug and fill with radiator flushing solution and water.

Restart the engine and run until the temperature gauge is at its normal position. Set the heater to its highest position. Switch off and allow the engine to cool then drain the radiator completely.

Fill the radiator with water through the radiator cap and tighten the cap. To most effectively bleed the air pour the water slowly and press on the upperlower radiator hoses. Start the engine and allow to come to normal operating temperature.

4 The coolant reservior fill cap removed. 5 Plastic bottle cut and used as a funnel. Y our C5 Corvette requires that you drain and refill the coolant in the radiator every 5 years or 100000 miles and every 3 years or 36000 miles thereafter.

In order to do the job you need three gallons of coolant.