14
Oct
Visit San Leandro Chrysler Dodge Jeep Ram serving San Francisco Oakland Hayward Berkeley CA. 3 On a manual window use the crank to roll down the window halfway to give you access to the bolt that holds the window to the regulator.
Step 1 Open the door of your Jeep Grand Cherokee all the way exposing the hinges between the door and the body.
Jeep grand cherokee door panel removal. Check all wiring to make sure it is routed correctly under all of the tabs along its path. Hold the door panel parallel to the door. Reach inside and reconnect the large main electrical connector and for the front drivers door the two-pin white memory mirror connector if equipped.
Reattach both metal rods and snap their lock clips into place. This is how you remove a door panel on a 2000 Jeep Grand Cherokee Laredo. This is also how many other door panels come off.
Be sure to subscribe for future u. Pull Out Pop Rivets. Pull Off Plastic Door Panel.
Insert the large flathead screwdriver or an automotive panel pry bar tool in to the bottom of the door panel and pry out the white plastic pop rivet friction fasteners. Continue pulling out the pop rivets all along the bottom and two sides of the panel. Removing the door panel of the Grand Cherokee WJ 99-04 is a easy task which allow you access to the mirrors bolts window and door lock mechanism.
You will need the following tools. Torx screwdriver T20 The work itself is pretty easy. Using a small flat screwdriver remove the plastic circle.
The Grand Cherokee is a confidently capable SUV with the credentials to back it up. From an available Best-in-Class towing capacity of 7200 pounds to its legendary available 4x4 capability Grand Cherokee has power and strength in its DNA. New 2018 Jeep Grand Cherokee Limited for sale - only 34480.
Visit San Leandro Chrysler Dodge Jeep Ram serving San Francisco Oakland Hayward Berkeley CA. Remove the Kick panel under the dash and disconnect any wire harnesses coming from the door. Pull the rubber seal then push it through the hole towards the door.
2 Pull back the rubber door gasket from between the door and the body of the vehicle. Remove the door opener handle from the opening in the door panel. Press in the release tab on the green plastic electrical connector before sliding it straight out of its socket.
Slide Out Grey Power Plug. Press the release tab on the grey plastic power plug before sliding it straight out of its socket. Set the plastic door panel aside in a safe place.
Remove Torx T-20 Screws. Hold Panel Near Frame. 1 each at the lower back of the door panel 1 each at the door release handle under a round push in cover.
Use a small flat tip screw driver to pop the cover off. From this point there are many push in type clips dont know if that is the wright name that hold the panel in place. I start at the bottom as the panel will have to be lifted off the top edge.
After the door panel is free from the metal door frame there will be an electrical plug to remove from the switch. Just push the tab in and pull the plug to remove it. Be careful not to apply too much force or the switch can come apart.
If the door handle connecting rod is still connected to the handle release the plastic catch and remove the rod. Thats it for the door panel removal. All right so lets pull a door panel off of a 95 Cherokee.
Its not too bad but if youve never done it before you might not know exactly how to get the sucker off. So really the only tool that you need is a Philips screwdriver but you also might want a little pryer too if you want to save those plastic clips and save the panel you can use this to help save those little clips. Replacing the door panel retaining clips on my 1996 Jeep Grand Cherokee100pc Door Panel Clip Trim Fastener For Jeep Grand Cherokee 6503204 For Chryslerhttps.
Step 1 Open the door of your Jeep Grand Cherokee all the way exposing the hinges between the door and the body. If your Jeep has power windows door locks or speakers in the door there will be a rubber boot running from the body to the door to protect the wiring. Jeep Grand Cherokee door panel pop tabs and tees will wear out over time resulting in a loose fit.
This can be fixed by just about any DIY repair man or woman with a few simple hand tools you most likely already own. Each door panel has 10 tees that will need to be replace to put your Jeep back together and have it fit like it was factory. Remove trim plug from mirror flag bezel.
Remove three screws attaching trim panel to door. Using a trim stick C-4829 or equivalent detach trim panel perimeter push-in fasteners from door inner panel. Lift trim panel upward and separate from door.
Pull or cut out the glued door seal to allow access inside the door. 3 On a manual window use the crank to roll down the window halfway to give you access to the bolt that holds the window to the regulator. If its an electric window use a battery from a cordless drill to jump the window motor till the bolt is showing.